Area 419 Improved Scope Base Rail for Various Firearms – Various MOA Configurations
CZ 457
This design, made from a single piece of T7075 aluminum and machined in house on our Haas VF4SS 4 axis machining center is designed to slide onto the dovetail and be clamped down with a force that is consistent across the entire rail – and strong enough that your CZ457 will never budge it. Bases will come Type III black hardcoat anodized and will come with the necessary wrench for torquing the clamp screws.
Recommended torque spec: 22 in/lb (2.5 NM)
Remington 700 Short Action
At Area 419 we decided that there were no scope bases on the market that really met our requirements for quality, so we made our own. Its all in the little details that set this base apart from the competition. These are machined in house on our 4-axis HAAS VMC from 7075 Aluminum. Straight off the mill there is not a single sharp edge left, all corners are radiused and any necessary harsh corners are chamfered. Just like all of the other Picatinny products we make, we radius between the slots, and also radius the corners of the lugs to prevent any snag areas and give it a cleaner look.
- Integral machined in recoil lug bears against the front receiver ring to prevent any base shifting under recoil
- Available in two versions, “Full Slotted” and “ARC Top”
- Full Slotted is compatible with all picatinny scope mounts including Spuhr and MPA which have a recoil lug in the center of the mount
- ARC Top is an Area 419 original design, mainly for aesthetics just to set it apart (will not work with mounts like Spuhr or MPA)
- Compatible with #6 and #8 screws, no modification necessary
- All mating areas are 1:1 surface machined to exact profile of the Remington action for a solid fit
- The MOA angle, or lack of angle, of the base is guaranteed to be true to the spec due to advanced fixturing
- Machined to MIL-STD-1913
- Ejection port cut blends seamlessly into action and gives plenty of room for top loading ADL style rifles
- Type III Hardcoat Black anodized
- (4) 6-48 and (4) 8-40 Torx T10 screws and wrench included
- All screws are the same length and sized to not interfere with barrel threads, no more guessing which screw goes where
- #6 Screws = 15in/lb
- #8 Screws = 20in/lb
BERGARA PREMIER FIT INFORMATION: If your serial number prefix is A00000-F00000 you have a round action that has the hood over the recoil lug, and this rail WILL NOT fit. Serial numbers G00000 or higher are the Remington pattern with 8-40 holes and this rail WILL work.
Tikka T1x
At Area 419 we decided that there were no scope bases on the market that really met our requirements for quality, so we made our own. Its all in the little details that set this base apart from the competition. These are machined in house on our 4-axis HAAS VMC from 7075 Aluminum. Straight off the mill there is not a single sharp edge left, all corners are radiused and any necessary harsh corners are chamfered. Just like all of the other Picatinny products we make, we radius between the slots, and also radius the corners of the lugs to prevent any snag areas and give it a cleaner look.
- As with our 700 rails, all screws are T10 Torx and the same length so no guessing which goes where
- The MOA angle of the base is guaranteed to be true to the spec due to advanced fixturing
- Machined to MIL-STD-1913
- Type III Hardcoat Black anodized
- Comes with a T10 Torx key
- Screw Torque = 15in/lb
CZ 455
This design, made from a single piece of T7075 aluminum and machined in house on our Haas VF4SS 4 axis machining center is designed to slide onto the dovetail and be clamped down with a force that is consistent across the entire rail – and strong enough that your CZ455 will never budge it. For added security we have added a recoil lug at the rear of the base, creating a mechanical stop for the base. Bases will come Type III black hardcoat anodized and will come with the necessary 2.5mm wrench for torquing the clamp screws. Recommended torque spec: 22 in/lb (2.5 NM)
These rails can also be used with the CZ 452, excluding the “American” model, which has a differently-sized dovetail.
Tikka T3/T3x
At Area 419 we decided that there were no scope bases on the market that really met our requirements for quality, so we made our own. Its all in the little details that set this base apart from the competition. These are machined in house on our 4-axis HAAS VMC from 7075 Aluminum. Straight off the mill there is not a single sharp edge left, all corners are radiused and any necessary harsh corners are chamfered. Just like all of the other Picatinny products we make, we radius between the slots, and also radius the corners of the lugs to prevent any snag areas and give it a cleaner look.
- Comes with stainless recoil pin to work with receivers that have the hole available, rail will still work on those that do not
- As with our 700 rails, all screws are T10 Torx and the same length so no guessing which goes where
- The MOA angle of the base is guaranteed to be true to the spec due to advanced fixturing
- Machined to MIL-STD-1913
- Type III Hardcoat Black anodized
- Comes with a T10 Torx key
- Screw Torque = 15in/lb
- Fits Tikka T3 and T3X
Remington 700 Long Action
At Area 419 we decided that there were no scope bases on the market that really met our requirements for quality, so we made our own. Its all in the little details that set this base apart from the competition. These are machined in house on our 4-axis HAAS VMC from 7075 Aluminum. Straight off the mill there is not a single sharp edge left, all corners are radiused and any necessary harsh corners are chamfered. Just like all of the other Picatinny products we make, we radius between the slots, and also radius the corners of the lugs to prevent any snag areas and give it a cleaner look.
- Integral machined in recoil lug bears against the front receiver ring to prevent any base shifting under recoil
- Available in two versions, “Full Slotted” and “ARC Top”
- Full Slotted is compatible with all picatinny scope mounts including Spuhr and MPA which have a recoil lug in the center of the mount
- ARC Top is an Area 419 original design, mainly for aesthetics just to set it apart (will not work with mounts like Spuhr or MPA)
- Compatible with #6 and #8 screws, no modification necessary
- All mating areas are 1:1 surface machined to exact profile of the Remington action for a solid fit
- The MOA angle of the base is guaranteed to be true to the spec due to advanced fixturing
- Machined to MIL-STD-1913
- Ejection port cut blends seamlessly into action and gives plenty of room for top loading ADL style rifles
- Type III Hardcoat Black anodized
- (4) 6-48 and (4) 8-40 Torx T10 screws and wrench included
- All screws are the same length and sized to not interfere with barrel threads, no more guessing which screw goes where
- #6 Screws = 15in/lb
- #8 Screws = 20in/lb
Ruger 10/22
This design, made from a single piece of T7075 aluminum and machined in house on our Haas VF4SS 4 axis machining center is designed to fit precisely, and strong enough that your rimfire will never budge it – all while providing the elevation you need for longer shots. Bases will come Type III black hardcoat anodized and will come with the necessary wrench for torquing the clamp screws.
Recommended torque spec: 15 in/lb
Anschutz 1761
This design, made from a single piece of T7075 aluminum and machined in house on our Haas VF4SS 4 axis machining center is designed to slide onto the dovetail and be clamped down with a force that is consistent across the entire rail – and strong enough that your rimfire will never budge it. Bases will come Type III black hardcoat anodized and will come with the necessary wrench for torquing the clamp screws.
Recommended torque spec: 22 in/lb (2.5 NM)
Henry Lever Action (3/4 Screw Models)
This design, made from a single piece of T7075 aluminum and machined in house on our world-class CNC machining centers is designed to fit precisely, and strong enough that your rifle will never budge it.. Bases will come Type III black hardcoat anodized and will come with the necessary wrench.
Recommended torque spec: 15 in/lb
Our rails are available for the 3 or 4-screw receivers in 0MOA.
FIT GUIDE
FOUR-SCREW (Long Action) will fit the following Henry models:
H009, H009G, H009B, H009AW, H009GAW, H009CC, H009GCC, H009X, H009WL, H009GWL, H009BWL
H010, H010G, H010B, H010AW, H010GAW, H010CC, H010GCC, H010X, H010WL, H010GWL, H010BWL
H018-410 (with drilled and tapped receivers), H018-410R, H018AH-410
H024-3030, H024-35, H024-3855, H024-4570
Please note that this base will only fit H018-410 models with drilled and tapped receivers.
THREE-SCREW (Short Action) fits:
H006 (must be 2nd Gen with drilled/tapped receiver) and H012 Series hole spacing only.
Will fit the following Henry models:
H006, H006R, H006M, H006MR, H006C, H006CR, H006S, H006MS, H006CS, H006ML, H006MML, H006CML, H006D, H006D2, H006D3, H006D4, H006ES, H006TT, H006OM, H006GBA
H012, H012G, H012R, H012GR, H012AW, H012GAW, H012CC, H012RCC, H012GRCC, H012GCC, H012M, H012GM, H012MAW, H012GMAW, H012MRCC, H012GMRCC, H012MCC, H012GMCC, H012C, H012GC, H012CRCC, H012GCRCC, H012CAW, H012GCAW, H012CCC, H012GCCC, H012X, H012MX, H012CX
Sako Quad
This design, made from a single piece of T7075 aluminum and machined in house on our Haas VF4SS 4 axis machining center is designed to slide onto the dovetail and be clamped down with a force that is consistent across the entire rail – and strong enough that your Sako Quad will never budge it. For added security we have added a recoil lug at the rear of the base, creating a mechanical stop for the base. Bases will come Type III black hardcoat anodized and will come with the necessary 3mm hex key for torquing the clamp screws.
Recommended torque spec: 22 in/lb (2.5 NM)
Savage Short Action
This design, made from a single piece of T7075 aluminum and machined in house on our world-class machining centers is designed to fit precisely – all while providing the elevation you need for longer shots. Bases will come Type III black hardcoat anodized and will come with the necessary wrench for torquing the clamp screws.
Recommended torque spec: 15 in/lb
Our rail comes in a 20MOA cant as a great all-purpose mount.
This rail fits:
Savage New 110 Short Action, 10, 11, 12, 14, 16 (6-48 screws)
Savage New 110 Short Action (8-40 screws)
Ruger American Short Action
This design, made from a single piece of T7075 aluminum and machined in house on our world-class machining centers is designed to fit precisely, and strong enough that your rifle will never budge it – all while providing the elevation you need for longer shots. Bases will come Type III black hardcoat anodized and will come with the necessary wrench for torquing the clamp screws.
Recommended torque spec: 15 in/lb
Our rail comes in a 20MOA cant as a great all-purpose mount.
Browning X-Bolt
**COMING SOON**
Rangeview Sports Canada
Licensed Gun Store in Newmarket, Ontario
